[Jimmy]

Fixing Error code 1002 and 1011:

– On your Windows desktop, navigate to the Windows Settings application.
– Alternatively, press Windows + I shortcut key on your keyboard to open the Windows Settings screen.
– Select Update & Security on the Windows Settings page and choose Windows Security from the left side panel.
– Click the Virus & threat protection feature under the Protection areas column.
– Select the Run a new advanced scan option.
– Choose ‘Full Scan’ and click on the Scan now button.
– Now, wait until the Windows Defender Firewall scans and removes all the virus-infected files on your system automatically.
– You can also run the disk cleanup on your Windows to remove the accumulated junk files causing the Bitdefender Error Code 1002.
– Navigate to the search bar and type ‘cmd.exe’ to open the Command Prompt window.
– Give a right-click on the Command Prompt and choose Run as administrator.
– Click on the Yes button in the User Account Control(UAC) window if it prompts.
– Type ‘cleanmgr’ in the Command Prompt window and press the Enter key.
– Select the drives you wish to clean from the dialogue box and click OK.
– Now, Rerun the Command Prompt as administrator on Windows.
– Type the ‘sfs/scannow’ command and press the Enter key.
– It starts scanning your system entirely and gives the status of it.
– You are also suggested to update the Windows OS and reinstall the Bitdefender Antivirus application.

This will help to resolve you issue,
Regards,
Jimmy Wick

[Jimmy]

Avast Antivirus displays notifications about application activity, product updates, warnings, and alerts. To disable these pop-up notifications, follow the instructions in this article.

Disable pop-up notifications
– Follow the gif or steps below to disable pop-up notifications in Avast Antivirus:
– Open Avast Antivirus and go to ☰ Menu ▸ Settings.
– Select General ▸ Notifications
– Tick the box next to Use silent mode and turn off all pop-ups, alerts and messages.

Notifications are now silenced.

Greetings,
Jimmy Wick

[Jimmy]

How can I solve the Error?

Solution 1: Use authentic HP ink cartridges.

Solution 2: Printer rest

In some instances, taking out the ink cartridges and resetting the printer can resolve the error message.

– Turn the printer ‘on.’
– Have patience until the printer is idle and silent before you continue.
– Now, disconnect the USB cable from the rear of the printer.
– If the printer has any network or wireless connection, leave the printer connected to the network or the wireless connection.
– Now, take out the ink cartridges from your printer.
– Now, with the printer still turned on you should remove the power cord from the wall outlet and also the rear of the printer.
– Hang around at least for 60 seconds.
– Plug-in the power cord back into the wall outlet after that.
– Please keep in mind that HP Printer recommends connecting the printer power cord directly to the wall outlet.
– Re-connect the power cord to the rear of the printer.
– Turn the printer ‘on’ again if it does not turn on automatically.
– The printer may go all the way via a warm-up period.
– The printer lights might flash, and the carriage might move.
– Be patient until the warm-up period finishes and the printer is inactive and silent before you proceed.
– Re-insert the ink cartridges and then shut the ink cartridge entrance
– If you receive a message to print a calibration page, you should do the same.
– If you by mistake disconnected the USB cable, re-connect it again to the rear of the printer.
– Now finally, try to print.

Hope this helps you out,
Regards,
Jimmy Wick

[Jimmy]

Windows Update Error 0xc1900223:
To fix Windows Update Error 0xc1900223, follow the below suggestion:

– Run Windows Update Troubleshooter
– Run Media Creation Tool
– Disable your VPN software
– Flush the DNS cache
– Perform DISM and SFC tools
– Reset Windows update component

Regards,
Jimmy Wick

[Jimmy]

Steps below to resolve error:

Turn off IPv6
From the home screen on the printer control panel, swipe the display to the left, and then touch Setup.
Touch Network Setup, and then touch Advanced Settings.
Turn off IPv6, and then touch Yes to confirm.

Update the printer firmware
Update your Printer firmware

Hope this helps you,
Jimmy Wick

[Author]

Posts